RFID work-in-progress (WIP) tracking in manufacturing
Where is this work order right now? Without walking the shop floor, nobody knows.
WIP tracking tells you in real time where every batch is and which step it has reached. With RFID, each container is read at the workstation or when it passes a gate, with no manual entry. The paper traveler gives way to reliable data that feeds your MES or your ERP directly.
What the paper traveler really costs
The paper traveler, or route card, follows the batch from one workstation to the next. It works as long as everyone fills it in at the right time. In practice, four problems keep coming back.
Late data entry
Progress is reported at the end of the shift or forgotten. Planning works on a false picture of the shop floor.
Invisible WIP
Between two workstations, the batch no longer exists for the system. Nobody knows whether it is waiting, blocked or moved.
Time spent searching
Finding an urgent batch means walking the shop floor and asking the teams.
Traceability rebuilt after the fact
When a non-conformity occurs, paper records are cross-checked to find out who did what and when.
Paper traveler, barcode or RFID?
RFID is not always the right answer. The right choice depends on the production rate, the number of batches in circulation and the movement you can ask of the operator.
| Criterion | Paper traveler | Barcode | RFID |
|---|---|---|---|
| Data capture | Manual, by hand | One scan per batch, aiming at the label | Automatic, no aiming |
| Information delay | Until it is keyed in | Immediate if the scan is done | Immediate, on the pass |
| Reading several batches | No | One by one | Several containers at once |
| Moves between zones | Not traced | Traced if the operator scans | Traced with no action, under a gate |
| Cost per batch | Paper and data entry time | A printed label | A tag, often reusable on the container |
| Best suited to | Small runs, few workstations | Moderate rate, easy scan at the workstation | Many flows, buffer zones, contactless reading |
Many shop floors combine both: barcodes at the workstation, RFID at the passages between zones.
Where to read WIP on the shop floor?
Read points go where the information changes: start and end of an operation, change of zone, end of line. Four setups cover most shop floors.
At the workstation
An antenna under the work surface reads the bin placed by the operator. Start and end of operation are recorded with no data entry.
Between two zones
An RFID gate reads the carts and containers passing through, with no stop or special movement.
At end of line
An RFID tunnel reads all the containers on a conveyor at once, before inspection or shipping.
In buffer stocks
A mobile terminal finds a specific batch in a waiting zone or a line-side store.
At the end of an assembly line, this RFID tunnel designed by CIPAM reads the chips of all the parts in a bin and compares the result with the bin label. If there is a mismatch, the bin is blocked.
The choice of readers and antennas and their tuning are done on site, workstation by workstation.
What should you identify: the container or the part?
On most shop floors, you identify the carrier: the bin, the cart, the pallet or the part holder. The tag is fitted once and lasts for years. The system links the container to the batch or work order at the start of the flow, then unlinks it at the end.
You identify the part itself when it must be traced unit by unit or when it leaves its container during the process. Two options: a suitable RFID tag or a DataMatrix code engraved by laser marking.
Constraints to check
- Metal, which requires on-metal tags
- Heat from ovens and curing ovens
- Washing, oils and chemicals
- Impacts and handling
Our RFID labels and tags cover these environments. For containers that circulate in a loop, see also reusable container traceability.
The container
Bin, cart, pallet or part holder. A reusable tag, linked to the batch at each cycle.
The part
Embedded RFID tag or engraved DataMatrix, when unit traceability is required.
The environment
Metal, heat, washing: the tag is chosen after a test in real conditions.
What feeds your MES or your ERP
Each read becomes a timestamped event: this batch entered this workstation at this time. The software deduces the actual progress of each work order.
Real-time progress
Start and end of each operation, waiting time between workstations, batches late against the schedule.
The operation context
The workstation, the operator if they badge in, the machine and the timestamp of each step.
Batch traceability
The full history of the route, ready for an audit or a non-conformity analysis.
The WIP metrics you get
Throughput time
The actual time between the release of a work order and its exit from the line.
Waiting times
Where and for how long batches wait. This is where bottlenecks hide.
WIP per zone
The number of batches at each step, at any time.
Late work orders
Orders drifting from the schedule, spotted before it is too late.
With scrap declared at the workstation, you also track non-quality step by step.
What to check before deploying
A shop floor is not a warehouse. Machines, metal and dense flows call for a few checks before any roll-out.
Stray reads
A workstation reader must not read the bin at the next workstation. Antenna power, orientation and shielding are adjusted accordingly.
Surrounding metal
Machines, workbenches and metal racks reflect radio waves. Antenna placement is validated by an on-site test.
Production rate
At high rates, read time must remain invisible to the operator and to the line.
Business rules
What does the system do when a batch skips a step or goes back? These rules are defined before deployment.
The operator movement
The read point follows the natural movement. If tracking adds a step, it will be bypassed.
Network and power
Each read point needs network and power. PoE often simplifies installation.
Deploying WIP tracking in six steps
You do not start with hardware. You start with the question tracking must answer: where is the batch, where is it waiting, who processed it?
Map the flows
Workstations, waiting zones, passages and the work orders concerned.
Choose what to identify
The container or the part, depending on the traceability level required.
Test in real conditions
Tags and antennas among the machines, before any commitment.
Equip a pilot line
A limited scope to measure the gain and adjust the rules.
Connect to your information system
MES, ERP or dedicated application, so that the data serves production control.
Extend and maintain
Other lines, other zones, with the integrator’s support.
The role of the integrator
A WIP tracking project combines hardware, software and your information system. The integrator keeps it consistent, from the survey to maintenance.
The site survey
Flows, workstations, read constraints and existing infrastructure.
The hardware
Tags, readers, antennas, gates and terminals from several brands. CIPAM is a Zebra partner.
The software
Batch statuses, delay alerts, history and dashboards.
The integration
Connection to your MES, your ERP or your WMS.
The deployment
Installation, on-site tuning and team training.
The follow-up
Maintenance, upgrades and new read points.
CIPAM has been integrating traceability solutions for over 30 years, on more than 400 sites in France and Europe.
An assembly line where every work order is tracked in real time
An automotive supplier, on its sun visor line for a German carmaker.
Each sun visor was packed in a bag with a barcode label. Operators reported their production by hand in the ERP. These steps added no value and the content of a bin could differ from its label.
What CIPAM designed
- An RFID chip in the sun visor frame, encoded at the end of assembly with the current work order
- Touch screens at the workstations: progress of each work order, parts welded, assembled and scrapped
- An application connected to the ERP, which triggers the printing of bin labels
- An RFID tunnel at the end of the line, which checks the quantity and part number of each bin
- Operators no longer report their production by hand
- The progress of each work order is visible in real time, workstation by workstation
- Each bin is checked before it leaves the line. If there is a mismatch, an alarm goes off and the bin is blocked
- The line has been in production since 2021. CIPAM provides its maintenance and upgrades
What you gain
A visible shop floor
Every batch has a position and a status. Planning works on the reality of the shop floor.
Less time lost
No more searching for urgent batches. No more keying in progress at the end of the shift.
Defensible traceability
The history of each batch is recorded as it happens, with no reconstruction after the fact.
Related solutions
Frequently asked questions
What is work in progress (WIP) in manufacturing?
Work in progress is any product whose manufacturing has started but is not finished: a part between two operations, a batch waiting in front of a machine, a sub-assembly on the line. In accounting, WIP is the value of these unfinished goods at closing. On the shop floor, the real question is where they are and which step they have reached.
What is RFID WIP tracking?
RFID WIP tracking identifies each container, carrier or part with an RFID tag and reads it automatically at workstations, between zones or at the end of the line. Every read becomes a timestamped event, so the software knows in real time where each batch is and what step it has completed, without manual data entry.
What are WIP tags?
WIP tags are the identifiers attached to work in progress so that it can be tracked from one step to the next. They can be barcode labels, but RFID tags are preferred when reads must be automatic: a rugged reusable tag on a bin or carrier, an on-metal tag on a metal part, or an RFID label printed and encoded when the work order is released.
RFID or barcode for WIP tracking?
Barcodes are enough when a unit scan fits naturally into the operator’s movement. RFID is the better choice when you need to read without line of sight, read several containers at once or record a pass without any human action, for example under a gate between two zones.
Do you need an MES for WIP tracking?
No, but you need software that turns reads into statuses. Depending on your information system, this can be your MES, your ERP or a dedicated application. CIPAM is a Qubes partner and also integrates RFID with the MES and ERP you already use.
Can you keep your current ERP?
Yes. RFID reads feed your ERP through its existing interfaces: progress reporting, component consumption, work order closing. The project does not replace your system, it feeds it with reliable data.
Are metal parts a problem?
Metal disturbs RFID reads, but some tags are designed to be mounted on metal. Often the container is identified rather than the part. When the part itself must carry its identifier, a DataMatrix code engraved by laser marking is a durable alternative.
Can you rebuild the genealogy of a batch?
Yes, if each step links what goes in and what comes out: component batches consumed, container, workstation and operator. The software keeps these links and traces a finished product back to its original batches. This is what makes targeted recalls and quality audits possible.
What KPIs does WIP tracking give you?
Throughput time from release to end of line, waiting times between steps, WIP level per zone and late work orders. With scrap declared at the workstation, you also follow quality step by step.
How much does RFID WIP tracking cost?
It depends on the number of read points, the type of tags and the integration with your information system. A site survey gives a reliable estimate for your shop floor.
Finally see your work in progress
Tell us about your flows, your workstations and your current system. We will suggest a pilot line.
- The useful read points, workstation by workstation
- Tags suited to your containers and parts
- A scoped pilot before any roll-out